Best Alternatives to RedeCanais4k.me for Free Streaming
If RedeCanais4k.me isn’t working for you, there are several excellent alternatives for free streaming. Websites like PelisPlus, Tubi, Crackle, and Popcornflix offer a wide range of movies and TV shows...
View ArticleClik here to view.
NI8452 - Open drain DIO
Hello, I would like to know if the DIO ports of the NI-8452 interface actually support open drain. There are inconsistencies in the manual; in fact, on page 45 it states this, while at the end of the...
View ArticleHigh Network Traffic Between USRP and gNB Even Without User Data
I'm experiencing high network traffic between my USRP and the gNB, even when no user data is being transmitted. When monitoring the interface with ifstat, I notice continuous data flow. Setup...
View ArticlePXIe_6570_Clock rate
Hi all,I have an issue getting a clean clock waveform at 5 MHz on the 6570. I tried to run with lower Speed at 1.1MHz, it looks good which is not the speed I want.Here are clock waveforms at 1MHz and...
View ArticleDigital Triggering
I want to trigger the laser and camera at the same time. Also, I have to give triggers at different frequencies. That to two lasers are triggering at 5 microseconds gap. I want to use it in PIV. I am...
View ArticleNI-9481 vs NI-9482
Hi, I understand that the NI-9481 is now obsolete. I noticed that it looks similar to the NI-9482.I have two questions:Why did NI discontinue the NI-9481? Were there any known issues with it?Is the...
View ArticleMatlab to USRP 2940R connection error
Hello, I want to send the signal from one usrp2940r and receive it using another USRP2940. I use following codetx = comm.SDRuTransmitter(...'Platform', 'X310', ...'IPAddress', '172.16.4.43', ... %...
View ArticleClik here to view.
How to configure CLIP on the sbRIO-9627?
Hello! I am using sbRIO-9627 and trying to extend the Can bus and RS232 bus by using CLIP, but I have encountered a problem and have asked the details of the problem in the forum(How does the...
View ArticleRDIO vs. RMIO cable for an MIO PCIe terminal
I have very little electronics experience, so I apologize in advance if this question is inappropriate or dumb. I want to use analog voltage signals (0 to +10V) to control a device that is connected to...
View ArticleClik here to view.
USB-6525 SSR Output Current Limit
I plan to use the SSR outputs of the USB-6525 DIO device to control an inductive load as shown: The manual lists a current limit of 500mA on the SSR output pins:Is there internal protection against...
View ArticleClik here to view.
USB-6501 16-position (screw terminal) plug header CAD
Hello all, Does anyone have CAD for the plug headers for the USB-6501? The official CAD on the website is only for the unit itself, it seems....
View ArticleMultiple hardware outputs on one bus coupler Modbus register
Hello all, apologies if this isn't the best board for this, I couldn't decide between posting on LabView, Digital IO, Modbus, DQMH, etc. My question really will boil down to "am I missing an obvious...
View ArticlePCIe-6535B on Ubuntu: future support roadmap?
Hello, I have a PCIe-6535B in an Ubuntu system. As stated this post, PCIe-6535B is not currently supported on Ubuntu, as per the NI Hardware and Software Operating System Compatibility. However, in...
View ArticleClik here to view.
Error -2147220354 at nisyscfg.lvlib:Restart.vi:1680001
ok i have this crio connected on USB AN ETH, i can ping I can connect on ni max saysoftware on the PC isand the image is the same 2018radutility goesModel Model Code Serial Number MAC Address IP...
View ArticleUSB-6501 Output Drive Configuration Issue
Hello,I'm using a USB-6501 for my project, but I'm encountering an issue with the I/O configuration. By default, when the DAQ is connected to the PC, the output lines are set to active drive...
View Article