Jumping all pins on CB-50/100
Hello all, We use PCI 6515/6528 frequently and end up having to make massive jumpers across the terminal block in order to have consistency and less wiring. ie All PX.Y + will be 24V or PX.Y - will...
View ArticleniHSDIO hardware comparison with acquisition device
Hello, In my setup, I have 3 niHSDIO PXIe 6555. For a test, I need to use one device to generate a stimulus waveform. With the other devices, I only do acquisition. During the acquisitions I would like...
View ArticleSuggest a card to sample 96 inputs with 5us pulse
Hi,Could someone suggest a solution and NI card to sample 96 inputs with a 5us pulse. PCIe would be preferred. The test setup would consist of stimulating the unit under test (UUT) and then sampling...
View ArticleGenerating a square/sine wave output with FPGA cRIO (NI 9704, NIO 9401)
Hi all, This is my first post, so bear with me if I don't add everything needed to answer this question. I am using a cRIO (9074) in FPGA mode, along with a NI 9401 Digital I/O c-series and trying to...
View ArticleSending Digital Signal via Visual Studios
My set up is as follows: Comp1======USB-6509-CP======CP-100 I/O Connector Block I want to be able to make a program in Visual Studios 2017 that will send a signal from one of the screw terminal pinouts...
View ArticleNI9159 abd DSM?
Hello, I have a NI9159 with some C-Series modules installed and I’d like to use the Distributed System Manager to read from its DIs and write to DOs on the fly, for testing purposes; I understand that...
View ArticleTrouble generating 50MHz clock digital output with myRIO-1900, sbRIO-9602,...
Hi all,I'm trying to drive a DS92LV16 16-bit Bus LVDS Serializer/Deserializer chip using any NI FPGA I have my hands on. The problem is that this chip needs as a minimum a 50 MHz clock. My FPGA boards...
View ArticleChange detection in PCIe 6509 in shared board
I have a situation where I have multiple applications sharing the ports of a pcie 6509. This works correctly for static dio, However, when I set up a change detection, I can only set up on one...
View Article6025E connector upgrade path
We have been using 6025 PCI card for many years but it has since gone end-of-life. The product page recommends NI PCIe-6321 X Series board. My question is if there is an upgrade path for the 68 pin...
View ArticleNI-9229 Sensitivity
Hi, I'm working on developing seismic digitizer so, we trying to configure the NI-9229 to match the required specifications. Please, I wanna to know the NI-9229 sensitivity (what's the relation between...
View ArticleNI 9205 measure the voltage of a load with high current
I have a load. The voltage on it is less than 10 V. Due to its small electrical resistance, the current on it is over 2,000 A. Can I use NI 9205 to measure the voltage on this load?
View Articlehigh speed output of custom bits
Hi all.I am building my own communication message protocol and I am looking for NI device or HW to output voltages of 0s (<2.5V) and 1s (>2.5V up to 5V) at speed of 1 micro-sec per bit. Lets say...
View ArticleSynchronized TTL Output
Hello, I'm looking for a PXIe or PCIe card that can provide at least 8 TTL digital outputs. Any 4 of these TTL digital outputs will need to be synchronized in an arbitrary/programmable way (i.e.,...
View ArticleMeasuring current using a shunt resistor and a DAQ
Hey,I have been doing a current measurement system, which uses one or more DAQs to measure current using shunt resistors.I wanted to calculate (simplified) the resolution of the system and ran into the...
View ArticleSuggestions for NI Hardware for my testbench design?
Currently I am building a production level test bench which can handle a large quantity of devices under test. I am looking for an NI device which can measure the current/power consumption from...
View ArticleClik here to view.
Synchronizing of DO and AO with USB-6259
Hallo everyone, i use right now the device USB-6259, and wanna synchronize AO with DO. I connected the Ctr0-Sample-Clock with the Timing-Funktion of AO.My task is: DO with 1MHz, and AO with 1KHz, and...
View ArticleHow to choose logic family for reference clock?
I need my NI device (PCIe-6363) to lock onto an external 10 MHz signal. I understand I can do this via the RefClkSrc/RefClkRate properties of the relevant tasks. I got that to work well enough. How can...
View ArticleCamera Attribute Of GPIO
Dear AllI am using GigE camera and VBAI for vision inspection. If I am using one script its change the attribute of another script. How is this possible? Please share any document from where I can...
View ArticleQuestion about SCB-68A
I am connecting a photon counting head through SCB-68A with 6612. My questions are:1. The output of the photon counting head is TTL, which digital DIO termials should I connect to on the SCB-68A, P or...
View Article6036E
I would like to know if it is possible to purchase a 6036E I/O board and how much does it cost. I am in Bologna, who is your local representative?Sincerely yoursEnrico G. Campari
View Article