Triggering via exported RTSI1 signal
Hi I have four PCIe6535s and synchronizing them with "sample clock" and "start trigger" exported via RTSI line 7 and 1 respectivelly from one of the boards, operating in Master(4) Slave(1-3)...
View ArticleMultiple Digital I/Os on cDAQ-9187
Hello, I use a cDAQ-9178 and LabVIEW Version 11.0.1f2. I have amongst others a module NI 9375 and a module NI 9472 for digital output signals.I try to generate three digital output signals in one VI...
View ArticleHow to connect +5V external power supply to USB 6210 to increase current on...
Hi all, I am currently working on a project that requires me to power a linear actuator using a relay (HN22005). I currently have the NI USB 6210. My idea was that i was going to use a digital output...
View ArticleUSB 6008 digital output
Hello, I'm new to labVIEW and using DAQ cards. I've been trying to run the "test panels" program to successfully get my card to output a 5V signal on any of the lines in port 0 or 1. When I set port 0...
View Article(france)) watch streaming Salaud, on t'aime [FUll Movie HD]
WATCH MOVIE ONLINE , FREE STREAMING WATCH Salaud, on t'aime FULL MOVIE ONLINE . WATCH FULL MOVIE Salaud, on t'aimeGenre :Release Date : 2014-04-02WATCH or DOWNLOAD NOW ==>...
View Articlesynchronizing several PCIe-6535B
Hi I need to synchronize all DOs in four of the PCIe-6535B. They are all connected with the RTSI cable, operating at 5MHz sample rate. All 128 lines need to start outputing the data when a single PFI...
View ArticleNI 9401 How fast can I switch the output on off
Using a 9174 chassis and NI 9401 Digital I/O I can not get the output to switch faster then 10 ms. I would like to have the output turn on off @ 15Hz 9% duty cycle which would roughly be 6ms on 66ms...
View ArticleNI 9234 and Accelerometer PCB 320C18
Hi, i have the NI 9234 which i used under MATLAB and it works. I connect to the NI 9234 the PCB 320C18 Accelerometer. I receive data from the acceleromter and the NI 9234. My Question is:what is the...
View ArticleHow to power a Cartridge Heater using LabVIEW
I have some new equipment from a supplier who uses a piece of software from a company called Hitec Zang. I'm trying to replicate what they use in LabVIEW as this is our main software system we use...
View ArticleInterfacing
Here i interfaced a GPS module which is working at 20Hz, with Arduino 2560 & receiving d data at pin no. 10. But I want to see that gps data in LabView by interfacing arduino with it. How can I...
View Articlepulse width modulation on sbRIO 9631
need to control 150 RPM DC motor with help of pulse width modulation from sbRIO 9631. need a simple VI in which i can take some DIO's and with help of a slider i can increase or decrease speed of motor...
View ArticlePXIe6556 - How to change output voltage during the generation?
I would like to know if is possible to change the output voltage (data lines) during the generation? 1. Start Generation - Vout=1V2. Change output voltage without stop the generation to Vout=1.2V3....
View ArticleUSB6009 limitation in a while loop
Dear labview colleages, Good morning, I have some trouble with the hardware device USB6009 and the width time of a analog voltage output.The algorithm (see picture) are included in a while loop and can...
View ArticleNI USRP-2942R の I/O のピンアサイン
こんにちは：） NI USRP-2942R に デジタルエッジトリガーを入力したいのですが、 デジタルIOのピンアサインがわかる方はいますでしょうか。 ありがとうございます：）
View ArticleCRIO's acquisition capacity
Hi,I'm using CRIO to acquire digital inputs, and each one requires a frequency of 1kHz, in this case I'm Afraid to exceed CRIO's acquisition Capacity knowing that CRIO requires a frequency less than...
View ArticleMaintaining previous idle state while loading a waveform
Hi, Is it possible to generate waveform1, in idle state hold the last bits of waveform1 (using 'X' in the idle state function), then load waveform2 while still maintaining the idle state from...
View ArticleNI 9474 TTL cDAQ-9178
Hi, I was wondering if a cDAQ-9178 chassis paired with a NI 9474 module would be capable of creating (3) unique 0-5V TTL signal? Would there be any obvious disadvantages to taking this route? Thanks...
View ArticleDIO - Single Line vs Port (U8) Write
I have a wierd situation: I am using a NI 6509 Digital I/O card, with 4x digital outputs connected to P2.3 thru P2.6. 1. I setup a task to write to these lines using a group of global virtual channels...
View Articlememory device chip select
hi all,I need your help here.actually i am planning to write a code in labview for the purpose of memory read write for an IC.here i need to test the memory device for different perameters like...
View ArticleUSB-8451 chip select lines while talking I2C
I intend to use the USB-8451 to communicate with a large number of I2C devices.A power switching and monitoring device will contain a CAT9555 (An I2C DIO chip) and 3 x I2C current monitors.there will...
View Article