Linux Drivers for High Speed Serial PXIe-6592R?
Are there Linux Drivers available for the High-Speed Serial Board (PXIe-6592R), and if not, are they planned on being released? Also, I could not find the LabVIEW 2016 compatible version of the...
View ArticlePort/Pin connection chart for cDAQ 9171
I'm looking for a diagram and/or table that lists the ports and their respective pin numbers for the 9171 USB Chassis. Does such a document exist?
View ArticleControl DIO of ni-845x in matlab
I'm trying to access the general purpose digital io of NI-8451 with matlab. I found many example how to control I2C and SPI of NI-8451 but I couldn't find the example regarding the DIO. Is there any...
View ArticleExtension cable for cRIO 15 D-SUB connector to NI 9220
Hi,I am solving very specifich aplication with cRIO and NI 9220. I need extend 15 pin D-SUB interface of cRIO by 1 meter cable. Problem is, that I can't find any information about connection of this...
View Articleni pxi-6541 (HSDIO)
hi, what all are the ways to generate waveforms( with different timing waveforms) and i would like to easiest ways to define our waveforms RegardsRaj kumar S
View ArticleCreate timing signals by NI PXI-6541
hi, i am going to generate a control signals by NI PXI-6541 which is going to control the ADC7862(analog to digital converter). In the IC data sheet they have to mentioned the necessary timing...
View ArticleUpper/Lower limits of PWM Frequency
Hello together, I am planning to control a DC-motor with the PWM-Output of a Microcontroller and I am not sure how to set the PWM-Frequency. The microcontroller update rate is 200Hz and the DC-motor...
View ArticleHELP with Advantech PCI1723 Analog Output
Hello everyone. I need serious help with the Advantech PCI1723 output. I need to generate an analog sine wave in one channel, but Static AO is the only scenario avalaible for my card.Any ideas? I'm...
View ArticleCan I measure the fan speed by NI 9401 & cRIO 9075 under Scan Interface?
Hi, I'm currently using NI 9401 & cRIO 9075 to develop a project, that is to control the CPU fans.Since I have to communicate with other instruments by serial port so that I have a module of NI...
View ArticleNI 9205 voltage reading error
Hi all,I have a 9205 analog input module, and in the past was able to read two single-ended analog inputs around 2.7-2.8 V correctly, on a Ethernet RIO 9148.However recently the module has stopped...
View Articleplease help
Hello everyone, First of all i don't know am right to start this topic under this location. My problem is: i am creating a square signal with simulate signal then i would like to count every peak...
View ArticlePCI 6503 on a PCI-e with raiser
I am upgrading the motherboard of our test system that uses 6 PCI slots including a PCI 6503 and a PCI-GPIB card. It is difficult to get a motherboard with 6 PCI slots. Question is will the 6503 and...
View ArticleGetting clock to run longer than CS signal in NI USB-8452 SPI
Hi, I am very new to SPI and not very versed with Labview but I when using the SPI VIs the clock pulses stop when the Chip Select goes from high to low. The application that I am trying to interface...
View Articleproblems with queuing (framegrabber PCIe-1433, Basler Sprint camera)
Hi. I am trying to get several images from my camera as soon as the trigger signal from a wave generator is read. I have a line-scan camera from Basler connected by two camera links to PCIe-1433...
View Article6541 available as a simulated DAQmx device?
In NI-MAX, when I attempt to add a simulated DAQmx device, I don't see the 6541 listed as a choice. Is this simulation perhaps available in a supplemental download?
View ArticleExecute Patterns in HSDIO 6556 with synchronizing SMU 4145
Hi All,I am using HSDIO 6556 to execute patterns which is already stored in HSDIO memory as a waveform.in between a pattern I want to Measure Current on some pins which is connected to SMUPlease...
View Article9401 driving a SSR
Is a 9401 module capable of driving a small (5amp) SSR with a 4-15 volt input?
View Articleafter certain amount of execution...Status Code: -200088
Hi,I am using USB6009 two DAQs with visual studio 2010 (c++), operating system window 8.1Previously, I have performed same kind of task without mutilple functions. Now I have increased no. of while...
View ArticleUSB 6008 to control two solenoid valve.
Hi,I want to control two 24VDC 3/2 way solenoid valve using the USB 6008 DAQcard. Now from previous posts and NI examples I have understood that I need a solid state relay than can switch with a 5mA...
View Article