PXI-8433/4 RTS/CTS line control
Hello, We have custom firmware for the 485 communication on our product. It uses the RTS line as a write enable and the CTS line as a loop back of the RTS. We were sold this PXI-8433/4 with the...
View ArticleC application using USB 6009 only works if NI Max is open
Hello,When running a simple C application using a USB 6009 device, a pulse is sent out on two digital lines, every 20 ms. The pulse length is 1 ms. The pulse is created by toggling the line high,...
View Articlecontrolling the digital output of PCI 6602
Hi, I currently have a PCI 6602 and want to use the digital output to output a voltage of 3V. Using a multimeter I have tested the 'on' output as 5V, is there a way to change this voltage? Thanks!
View ArticleClik here to view.
NI 9375 current specification
I'm trying to get my head around the NI-9375 continuous output current from the data sheet. The NI-9375 card is obviously a 16 DI / 16DO module, and with "all channels on" (presumably this is only...
View Articlecompatibility DIO 32HS with BNC 2121
Hi,I have a simple question concerning the compatibility of an old PCI-DIO-32HS card that I have available. Would this card be compatible with a DAQ block BNC 2121 and an SH-68-68-D1 cable that I would...
View ArticleUSB 6259 availability or replacement
I have used the USB 6259 DAC previously but it is not appearing as a current item. Are they still being sold, or is there an equivalent replacement part?
View ArticleCan a myRIO vary resistance?
Hi, I have a NI myRIO 1900 series and am wondering does the myRIO have the capability to vary resistance. Back Story: I have a motor which I want to control the speed of with a digital slider output on...
View ArticleDigital demodulation
I want know how can we convert the basic analog front end fm signal (before demodulation) into quadrature components and load it to matlab for software based real time demodulation. Could you plz...
View ArticlecRIO 9035 suddenly stopped scanning I/O
Our cRIO 9035 was running fine when it suddenly stopped scanning the I/O yesterday, after which the program just pops up error messages (...timeout, cannot [read input#/write output#]) one after...
View Article7820R default clip
I am trying to setup a labView FPGA project for the 7820R. I am able to create the FPGA project in labview 2018 but I don't have a component-Level IP file to be able to use the128 pins of DIO so I can...
View ArticleREGARDING SELECTING OF CRIO SYSYTEM
HI I AM AN ENGINEER WE WANT TO TO USE CRIO SYSYTEM BUT I COULDN'T HAVE KNOWLEDGE OF HOW TO CREATE A SYSYTEM. SO PLEASE GAUID ME WHERE I CAN ABLE TO DO .
View ArticleClik here to view.
Trouble with NI9403 using Input and Output mix in same module
Hi, I am working with a cDAQ9189 and I have 3 modules attached. One NI9205, other NI9403 and a NI9265. I made recently and a application with them and I use the example about continuous acquisition...
View ArticleHow to make LED blink in NI 9742 ?
Hello, I'm a beginner to electronics field.My task is to make LED blink in any sequence or flash using NI 9742 in NI cDAQ-9174.Please let me know how to complete this task.Iam using DAQExpress 4.0.0
View ArticleSb-RIO 9606 errorlog
Welcome NI Community,I'm writing to you with a treated problem.I currently us Sb-RIO 9606 as a home automation server which uses KNX and CAN standards. The user of the home automation system can log...
View ArticleNI MYRIO MAX30102
Hello, is MAX30102 sp02 and pulse rate sensor compatible with NI MYRIO? Thank youuu
View ArticleClik here to view.
Digital I/O Soft Front Panel (SFP) dissapeared
Hi all. I have an ELVIS III with the 'standard' Prototyping Board and I am trying to run some simple experiments for school. I am using Measurements Live and all the Soft Front Panel "instruments" work...
View ArticleReplacing mechanical potentiometer with digital potentiometer for myRIO
Hi,I wish to replace a mechanical potentiometer on a motor control board which is used to control the speed of a motor with a digital potentiometer. This will allow me to control the speed of the motor...
View ArticleWaterfalling Pulse on X-series (PCIe-6363)
I have a PCIe-6363 (and a PCIE-6536 next to it). The PCIe currently takes a digital edge trigger on PFI5, and then Uses Port 0 to marshall out a waveform. That works fine. Once that's done I need to...
View ArticleIs there an PCI or PCIe Differential IO card available to measure...
I have a system where I need to collect position data from a differential encoder. I know there is an option to do this using a Cdaq chassis with a NI 9411 Module but it would require me to...
View ArticleR100M-50F-50F Cable wire map
Hello,does anyone know where I can find the wire map or pinout of the R100M-50F-50F cable assembly.I can't seem to find that info anywhere on NI's site.
View Article