sbRIO-9627 simultaneous usage of all DIOs and ADCs
On the sbRIO-9627, can you simultaneously use all 100 DIOs and all 16-channels of analog inputs? I am confused because the sbRIO-9607 has the same SoC (Zynq-7020), but only has 96 DIOs and 0 analog...
View ArticleDIGILENT DIGITAL DISCOVERY
Good evening guys, I hope you are staying safe and happy. I recently purchased a digital discovery board for an application which is related to ADC but I was facing difficulties in recognizing the...
View ArticleDAQ digitizer error: PCI-5152
Dear NI, Our equipment could not get full working with NI PCI 5152, we suggested have issue with board as attached file. after that, we checked and found one component with name 1ft have defect look...
View ArticleNI 9375 DI COM pin connected to earth ground?
Hi, I would use a NI 9375 to check the state of some digital swithces, in a circuit with a +24V power supply. Inside the 9375 the lower end of the receiver circuitry (DI COM) is connected to GND, but...
View ArticleNI DIO serial or Parallel
Hi, What is mean by Serial Digital Input output module and Parallel Digital Input output module. Serial Digital Input module not support counters, eg:NI 9375 Parallel Digital Input output module...
View ArticleUse PCI cards in PXI chassis and c++
HI, I am currently using 2 PCI 6733 on an old experimental setup and I'm controlling the analog outputs of these cards using a c++ code.I want to upgrade the setup. Nowadays computers do not have many...
View ArticleI/O and Fusing - Each Card or Each Point?
I recently inherited a job in the water treatment business. It looks like the previous system designer fused EVERY SINGLE input and output point. This is overkill right? I have never ever fused each...
View ArticleProper card selection pulse input
Hello there I have the need for monitoring and counting fast flowsI have a flowmeter with the fast pulse outpu up to 10 KHz - typically working range 5...8 kHzscheme for pulse input page 20, 21...
View ArticleClik here to view.
Writing valuables on another opc
Hello i'm using 32 bit version of lv2012 for gonna make reset module of my wind turbines. But i need to insert some commands in my opc server on Vi,For ex; (it's a simple server request input which i...
View ArticleSC-2345 Power Suppy AC Cable
Can you guys provide the part number of the AC power supply of SC-2345. We know thew board inside the blackbox is the SCC-PWR02, but we want to buy the complete assembly with all the cables.Thanks in...
View ArticleThird part TCP-IP server (C++) to LabVIEW as TCP - Client ( How to decompile...
Dear Colleagues, I have an old third part TCP-IP server (WINSOCK SocketAPI) written in C++, which I need to communicate with LabVIEW playing the role of TCP Client to read and to write to the TCP...
View ArticleMeasuring the value of temperature sensor using RTD
I have a Pt1000 temperature sensor and I am having a hard time understanding the value I'm getting.The temperature should be around 20-25C and I am expecting to get a value of the resistance of around...
View ArticleClik here to view.
How to export digital output pulse wave simultaneously?
Hi, i have trouble using NI-9401. I want to export digital output pulse wave simultaneously, such as DIO/line2 and DIO/line3 in NI-9401. Shortly say, I hope export 1kHz sampling rate to DIO/line2 and...
View ArticleIs NI-9381 compatible with cDAQ-9188?
When I connect the NI 9381 module to cDAQ-9188. NI MAX reports unsupported module. Does that mean NI 9381 and cDAQ-9188 are uncompatible? I looked at this but it's not clear if this is specific to...
View ArticleUSB-6509 Compatible with HYT-271 Humidity Sensor
Hello, This is a relatively straightforward and simple question. I just wanted to ensure that the HYT-271 Humidity Sensor would work with the USB-6509 board I have? There are many posts regarding its...
View ArticleClik here to view.
[noob and basic] Fail to send 24V signal to valves with NI 9476
Hello,I do exactly what he does in this tutorial : https://youtu.be/F-3eX2Qf6pQ Code is just a while loop with DAQ assistant, nothing else. I own the NI 9476 and I am trying to send 24 V to on/off...
View ArticleI2C read - unable to read byte data from register
Hi, We are working on a solution that involves i2C communication between the XC7A35T-1FTG256C and FX3 development kit and are experiencing problems reading data from the FPGA registers.What we are...
View ArticleStandalone SW for USB-6509
Are there any SW running standalone and which may communicate with the USB-6509 DIO module?In the end our SW developers will use Labview/Teststand but in a bring up periode it is preferred to use...
View ArticleDAQmx buffer error in TestStand but not in LabVIEW
Hello super users, I am trying to use the cDAQ9174/NI 9475 to generate continuous pulses. My code works fine in LabVIEW. However, I run into buffer error when using the same code in TestStand (full...
View ArticleSynchronising digital output from PCI 6534 and PXIe 6535
I have two digital pattern cards, one in a desktop (PCI 6534) and one in a PXI chassis (PXIe 6535) that I would like to synchronise. I am using DAQmx in c#. I have been trying to use the one in the...
View Article