Sending Arduino Clock using Linx makerhub
Hello guys ! First of all sorry If the question as already been asked, but I did not find it yet, so i decided to ask mine 🙂 My issue is that I need to send the Clock from an Arduino Mega, to a DAC...
View ArticleUSB-6000 + NIDAQmx+ detect switch
Hello, I would like to recognize via a DI and a DO channel, if a contact is switched or not.For this I want to set the DO channel high (+ 5V)and wire this to the DI channel via a switch.Then I read out...
View ArticleC-series module for functional safety NI-9351
Hello, everyone,my group bought a C-series module for functional safety NI-9351 for experiment set-up.but after reading the Manual, I still not understand how it works and what does it work for. I...
View ArticleNI 9401 SPI Slave Devices
I see the NI 9401 can use SPI to communicate with a slave device and I see in the "NI 9401 Getting Started Guide" how to connect for SPI. From the description in the Getting Started Guide, it looks...
View ArticleClik here to view.
Controlling a solenoid valve using a NI USB-6501 with Labview
I am trying to write a Labview program to turn on/off a 120 V solenoid valve (wired to NI USB- 6501 through a SS relay which gives 3-5V output). The problem I'm facing is that when I run the VI, the...
View ArticleDAQMX Base install issue
Hi everybody, I have an NI USB 6501 card, which I use very well in python on Windows. but I would now like to switch to Ubuntu while using my python code.To do this I find that the NI USB 6501 card was...
View ArticlePFI Terminals BNC 2090A + PCIe-6363
Hello, I am using a PCIe-6363 multifuntion I/O devices connected to two BNC 2090A rack mount connector. I am trying to connect a PDM module to the DAQ counter. The module outputs a TTL signal. I am...
View ArticlePC-DIO-24 on Windows 2000 to PCI-6503 on Windows 7
Hello,I have an old Pentium PC running Windows 2000 that I have been using as part of a test setup with an Audio Precision System One. I am using a PC-DIO-24 to control external relays for automated...
View Articlenidaq32.bas and Windows 7
Hello, I have successfully installed NI-DAQmx on a Windows 7 64-bit machine. I can control a PCI-6503 from the test panel in NI-max. So far so good... I have a VB program that I was using on a Windows...
View ArticleConfiguring NI 9361 Terminal
I have 3 linear encoder and I will use NI9361. It wil be connected single ended encoder. But I do not need Z index signal. Can I configure it as digital input for error signal instead of Z signal? If...
View ArticleUsing LINX & Arduino to generate multi-channel digital write square wave
I am doing a program to generate multi-channel square wave by Arduino, I am using the "digital write square wave", but it can only generate one channel wave, whether any method can generate...
View ArticleBad SHC68-C68-D3 cable
I have a bad SHC68-C68-D3 cable.Symptom is some pins appear to be shorted to ground. Can it be repaired?Probably not, but it doesn't hurt to ask. If it can't be repaired, would NI be interested in...
View ArticleDC power supply shorted - NI sbrio FPGA board does not power up - any leads...
I accidentally shorted the DC power supply pins on the sbRIO 9612 board and my DC power supply had a very large current limit. Now, the FPGA board does not power up. To see if the fuse blew up, I...
View ArticleWriteNamedWaveformWDT and NI6562 - samplesPerChannel must be multiple of 4?
I'm relatively new to NI's PXIe boxes and the NI-6562 card, so I may be making a newbie mistake. I'm using the niHSDIO_WriteNamedWaveformWDT command to generate a dynamic signal with an NI-6562 card....
View ArticleUsing a digital I/O module on a cDAQ as a UART interface
Hi all!I have a cDAQ-9174 with an empty slot, and I need to communicate with a board which has a 3V UART interface. Can I use a digital input and a digital output of a digital I/O C-module in order to...
View ArticleValue change detection of a NI 9402 DO line using a LabVIEW event structure.
Is it possible to detect a change in the value of a NI 9402 Digital Output line using a LabVIEW event structure?
View ArticleDriver installation issue with USB-8451
Hello everyone : I try to install a driver of USB-8451 but now facing issue as below picture or attached file. Could anyone help me to solve the problem? I try again but not work. Even I try to...
View ArticlePCI 6220 Maximum Number of connected Thermocouples
Hello everybody, I have so many Themocouples "more than 800 themocouples" set to measure temperature. I'm planning to use NI DAQ 6220 PCI card "with its associated accessories" + Labview to monitor...
View ArticleUsing DAQmx USB-6003 in Linux Ubuntu
Hi, I am trying to use DAQmx USB-6003 in Linux Ubuntu 18.04. Here are the steps that I have already done: * I installed the Linux DAQmx drivers* I copied the examples of the ANSI C library...
View Article