NI USB-6009 no right clicking on measurement and automation explorer
I have a NI USB 6009 multifunction I/0. I have installed the DAQmx package, It shows up on NI MAX, but there isn't an option to right click. Once I load NI MAX it also initially gives me the error:...
View ArticleBest timing method for Digital Output for NI PXI 6527?
Hello, I am trying to improve the timing reliability of changing the digital output values for a NI PXI 6527. I have attached an image of a snippet of code demonstrating my current method of:-writing...
View ArticleNI USB-6501 and "DO.Output Drive Type" parameter
Hi all. I have a box, integrated in a TE, that houses a USB-6501 card.DI and DO are properly conditioned and can be accessed by a custom connector.A LabVIEW application controls the whole TE and, at...
View ArticleDigital Outputs on SCB-68A
We are working with SCB-68A connected to PXIe-1073 over DAQ Board PXIe-6363 and we need to connect some digital output signals for that matter I wanted to ask whether we should connect the to the PFI...
View ArticleClik here to view.
How to connect opto sensor and limit switch to DI module?
Hi, I have a opto sensor (OMRON EE-672) and a limit switch (OMRON V-156-1A5).I'd like to use them to detect the limit triggering of my stepper motor.However I have no idea how to connect them to my DI...
View ArticleLooking for Cables for PCIe 6509
Hi folks,for 2 days I've been searching for suitable cables for PCIe6509 cards. NI provides only 1 and 2 metres cables, but we need 5m (16ft) length. The only provider I found is Mouser/TE Connect, but...
View ArticleCalExec 4.1 PXIe-6556 "Session Handle Not Valid"
Hi All, In running calibration routine for PXIe-6556 I get the below error after self calibration portion is complete. I have run several PXIe-6556s with no issues until this point. Any thoughts?...
View ArticleMonitor multiple ports at the same time on PCI-6528
I would like to monitor all inputs on the PCI-6528 during a certain amount of time (not only one read), such that an eventual digital HIGH can be captured during that period in my C# application. I...
View ArticleLog events
Dear Forum members, We are using a custom build setup that drives behavioural experiment paired to a microscope. We created a driving program using the NIDAQmx C driver. The program runs an...
View Articlewhat modules to be used
Hi .. i would like to connect the following sensors to a Ni DAQ system: 1. pressure sensor • Honeywell -...
View ArticleHow can connect USB-6001 Digital Output to a relay?
Hi! I have an USB-6001 DAQ board and I want to use it to control a hydraulic system by using relays. But the digital output of the board is 3,3Vmax and 4mA max if I'm not wrong, and I couldn't find a...
View ArticleDAQmx with NI PXI-8840 eMBEDDED CONTROLLER
HII,I have a problem with the transmition of data throught a NI PXI-8840 for my screm . I don''t know if i can use NI DAQmx as software for the transmission .in this case my computer is NI PXI-8840 and...
View ArticlePCI-6542 - generating SPI comunication at high rate
Hello, We are considering purchasing the PCI-6542 and the auxiliary cable. we need some help determining if we can reach the SPI data rates we need with the card and the setup we are going to use. The...
View ArticleUSB-6501 all digital outputs fluctuate when one digital output is toggled on...
Hi Everyone, I have an USB-6501 connected to several electro-mechanical relays through digital out which control several solenoid valves. I also have one digital out pin connected to a fluid sensor...
View ArticleUSB6509 - Read c#
Hi,I have a problem with read implementation. I explain you.I need to read EEprom and so: 3 pin (chipselect, DI, clock) set output mode and 1 set input (DO). I initialize read port-pin: private...
View ArticleFunctional Safety NI 9350
Hi, I saw that NI released a functional Safety c-series module. If my understanding is good, this module work as a standalone module. Is it possible to use it on an EtherCAT chassis and can we program...
View ArticleProblem with SCC-TC01 module,
Hello colleagues, I'm using an SCC-2345 box with two TC-01 modules inside.I am reading temperature of a furnace with them. The problem is:1- None of the TC01 units read the temperature correctly.2-...
View ArticleUSB-6501 connector for OEM board
Hi... I have a USB-6501 board that I want to use on a board from another vendor, where that board was really made for the OEM version of the USB-6501. On my USB-6501 (non-OEM) board, it looks like its...
View ArticlePWM signal is going to 9423 and not the motor
I am trying to measure the PWM signal into a blower. So I wired the NI 9243 in parallel to the blower and I am able to read the digital signal. However, the voltage at 12V and the current at 3mA but...
View ArticlePWM signal is going to 9423 and not the motor
I am trying to measure the PWM signal into a blower. So I wired the NI 9243 in parallel to the blower and I am able to read the digital signal. However, the voltage at 12V and the current at 3mA but...
View Article