OM-USB-1208 ULx install Labview17
When I run the ULxForLabVIEW installer, I get the error "LabVIEW 2010 or later is required for this package".I have installed and licensed Labview 2017 32 bit version and am running Windows 7InstaCal...
View ArticleUSB-6221 MTBF
I'm trying to find MTBF estimates for USB-6221 or related product. This is desired by our U.S. Government customer. Appreciate any information that might help.
View ArticleNI PCIe-6509 I/O question
I was wondering if, for the NI PCIe6509, the lines can be changed as input/output on the run, meaning, if initially I set some lines as input I can change them to be outputs while I'm running a...
View ArticleUsing an External Digital Trigger to Read Digital Input Once
Hello, I am using the NI USB X Series (specifically the NI USB-6343) and programming in Visual studio 2010 with C# .NET . What I have been trying to do is use an external Digital trigger on Port 1...
View ArticleHow to input the information of load cell and rotary encoder into eZ-Analyst...
I would need to input the information of a load cell and a rotary encoder, which are connected to channels of IOTech 650U, to the eZ-Analyst software. I have the following information...
View ArticleClik here to view.
Digital Input as a Counter ... How to do it please help
Hi,Im new to the LavView programming and i have an NI USB-6008 DAQ.Can someone please explain me or e-mail me a code how can i use my digital input where i connected the push button as a counter so...
View ArticleNI 9403 timing hardware or only software
I'm confused on the NI 9403 documentation is it only software timing control? The specs say the 9403 cannot route clock and timing signal --> does this mean you cannot use hardware...
View ArticleDigital Output - Unwanted Reset on Lines
I am using MATLAB to change the values of my NIDAQ's digital outputs. The outputs are sent to the digital input of another device where they are recorded. Whenever the value of one of the output...
View ArticleGenerate PWM with frquency lower than 40 Hz
i'm using myRio to generate PWM signal. how can I get PWM frequency lower than 40 Hz, I would like to reach 10, 20, 30, 40 Hz
View ArticlemyRIO DIO level shifting from 3V to 5V
Hi,I am using a myRIO to output fast switching TTL signals to control a laser system. I used to do this using a DAQ but due to the conditions of the experiment we needed something faster so the myRIO...
View ArticleClik here to view.
Real Time Application on myRio
Hello, I have just started using Labview FPGA for a student project and have come across a small problem that I haven't found addressed here already: when I attempt to deploy a VI as a real time...
View ArticleRouting P0 to PFI on USB 6361?
Hi All, I'm attempting to use the DO timing features on the USB 6361 to drive an experiment. This requires me to do a buffered write and according to the error messages I've received on NImax, this is...
View ArticleHSDIO Custom Cable Issues
I took some old HSDIO SHC68-C68-D4 cables and cut the wires, cleaned off the board contacts of all wires, solder etc. I added 4 wires to connect to short coax for my DIO0 and DIO1 outputs or DIO2 and...
View ArticleDigital IO for a Load Cell using cRIO
Hi All, I am trying to read outputs from a load cell. The hardware is described at the link below (where it was suggested to the OP that they should use a...
View Articlei2c communication procedure
i am using USb 8452 module for i2c communication in between the LDC 1612 module(slave)and USB 8452 (master).How to configure and get the data?any idea or suggestions
View ArticleHardware specs
Hello everyone, I am using a SCB-100 board connected to a digital output device of NIPCI-6512 and we are using this to control pumps and solenoids. I am trying to figure out what is the max amperage...
View ArticleNI-Tclk Error 250043
Hi all,I have two chassis the first chassis has 5 VSA(s) NI PXIe-5663E and second chassis has 5 VSG(s) NI PXIe-5673E. today the system doesn't work and give me this error in the attached thread....
View ArticleNI 9482 - Current Measurement Through Relay Contact
The NI 9482 is exactly what I need to control 4 28v devices from a cDAQ, but I also need to measure the current that is being drawn on the 28v supplied to each of the devices. Can anyone confirm if the...
View ArticleWin 95/98 driver wanted for Lab-PC+ for Register Level Programming
Hi there, hopefully someone can help? I am looking for a driver for an Lab-PC+, Low-Cost Multifunction I/O Board for ISA, Part Number 320502B-0, for Register-Level Programming on Windows 95 / 98. Some...
View ArticleCan't compile with SbRIO 96006
Hi, I'm woriking with a sbRIO 9606, according with the tables 1 and 2 (http://www.ni.com/product-documentation/53056/en/), i have installed Vivado 2015.4 but when I try to compile my VI, it says "The...
View Article